Your Plumbing Crash Course: What You Must Have for Bathtub Installation
Your Plumbing Crash Course: What You Must Have for Bathtub Installation
Blog Article
We've come across this post on A Step-by-Step Guide to Installing a Bathtub listed below on the net and concluded it made good sense to write about it with you over here.
Installing a bath tub isn't specifically rocket science, however it does need strong plumbing, carpentry, and often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a moderately difficult project. If the old tub is readily obtainable, the task can relocate speedily; if you have to open up a wall to remove the old tub and also place the brand-new tub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will need a helper to move out the old bathtub and also embeded in the brand-new one. See to it you have actually certified yourself for the work and fit trying it. Instead of hiring a contractor to take over a halfway-completed task, it is much better to take into consideration utilizing one prior to you begin. Chances are you may require a professional plumber to make tube connections.
This short article will aid you set up a new bath tub in your washroom if you have already acquired a brand-new bathtub and also do not need to change the arrangement of your previous supply of water pipes.
Your tools as well as material checklist need to consist of the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be fairly troublesome due to the limited gain access to that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this process. Once the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Before moving on to fit the new taps, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, then you will need lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin making sure that the washers are in place in between the faucet as well as the sink. Safeguard the faucet in position with the maker offered backnut. Once the tap is firmly in position, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The former kind must be linked to the faucet finishes initially, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Using both wood boards under its feet, put the tub in the needed setting. The wooden boards are valuable in uniformly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 small factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level and adjusting the feet on the tub up until the spirit level reviews level.
To install faucets, fit the bottom of the outermost versatile tap port to the appropriate supply pipeline by making a compression join; then do the same for the other faucet.
Activate the water system as well as check all joints and brand-new pipework for leakages as well as tighten them if essential. Load the tub and also examine the overflow electrical outlet and also the typical outlet for leakages.
Lastly, fix the bath paneling as defined in the maker's instruction manual. Tiling and also sealing around the bath tub needs to wait up until the bathtub has actually been used a minimum of once as this will certainly settle it right into its final placement.
Preparing for the Installment
First of all, the sustaining frame provided with the bathroom ought to be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When fitting the tap block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its final placement.
Tiling Around the Bathtub
In the area where the bath satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to crack a rigid seal, triggering the water to permeate the wall in between the bathroom and the tiling, causing problems with wetness and also feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes as well as cartridges, and are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of drenched paper or soft rope. Keep in mind to constantly load the tub with water prior to securing, to allow for the activity experienced when the bathtub is in use. The sealant can split fairly early if you do not consider this motion before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily offered on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that piece of writing on A Step-by-Step Guide to Installing a Bathtub when doing a search on the internet. Feel free to take a moment to promote this blog if you appreciated it. We enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Plumbing woes? Connect. Report this page